PART 6

Name	Quantity	Required	Reponse
Models of Electrical Stations
Circuit Breaker (Q or CB) 22 kV	1
		Rated Voltage 25.8 kV
		Continuous Current 630A
		Frequency: 50/60Hz
		Rated shot time current 16 kA
		Rated making current:
		+ Asym: 16 kA
		+ Peak: 41.6 kA
		Number of Operation:
		Mechanical 5,000 operations
		Load Switching 400 operations
		Reted power Frequency:
		With stand Voltage Dry (1 min): 70 kV
		With stand Voltage Wet (1 min): 60 kV
Disconnection Device (DS) 22 kV	1
		3 x Single pole Disconnecting switches
		Rated kV: 25.8 kV
		Rated A: 600 A
Current Transformer (CT) 22 kV	1
		3 x Oil Type Current Tranformer
		Rated kV: 24 kV
		Rated A: 10 VA
		Range: 250 - 600 A/ 5A
Potential Tranformer (PT) 22 kV	1
		3 x Oil Type Potential Tranformer
		Rated kV: 24 kV
		Rated V: 110 V
		Rated VA: 25 VA
Zone Transformer 22/0.4 kV 160 kVA	1
		Outdoor type, Mineral oil Immersed
		Rated Frequency: 50Hz
		Rated Capacity: 160 kVA
		Rated Primary Voltage: 22 kV, 3 Phase 3 Wire
		Rated Secondary Voltage: 416V, 3 Phase 4 Wire
		Vector Group: DYN 11
Control Box Use for Relay in	1
		Consist of KWH Meter in outdoor box IP 65
		With control cable form CT., PT. included ground system
Pole 12 m	3	Electricity pole 12 m
Pole 8 m	2	Electricity pole 8 m
Lighting Arrester (LA) 22 kV	1
		Type SA (GK)
		Rated kV: 24 kV
		Rated kA: 10 kA
		According to IEC 60099-4
Electrical Practice Equipment
Load Center Phase 220 V, 12 locks	2
		Load Center Consumer Unit
		For 12 modules
		1 phase, 2 wire, 240BV with ground bar
		According to IEC 60439-1
Load Center Phase 380 V, 18 locks	3
		Load Center Consumer unit
		For 18 Modules
		3 phase, 4 wire, 240/ 415 V with ground bar.
		According to IEC 60439-1
Digital Ground Tester	3
		Earth Resistance Tester are small, light weight and dust proof.
		Measurement range 0-20/ 0-200/ 0-2000 ohm
		Earth Voltage 0 - 200 VAC, 50 Hz
		Overload Protection
		Safety Standard IEC 61010-1
Mega Ohm Meter	2
		Insulation tester combine a true-rms digital multimeter
		- Insulation test voltage 50V/ 100V/ 250V/ 500V and 1000V
		- Insulation test 0.01 MΩ to Z GΩ
		- Auto - discharge of capacitive voltage for added user protection
		- AC/DC voltage, DC miliVolts, AC/DC miliampes, Resistance, Continuity
		- Capacitance, Diode test, Temperature, Min/Max, Frequency
Digital Multi Tester	4	True - rms AC voltage and current for accurate measurements on non-linear signals.
		AC/DC votalge: 600 V
		AC/DC Current: 600 A (via jaw)
		Resistane: 6000 ohm
		Frequency: 500 Hz
Current Transformer	12	Rated current 50/5A, 1VA
		Window size 30 x 20 mm
		Rated voltage: 600 VAC
		Operating Frequency 50/ 60Hz
		Class 1.0
		Case ABS Plastic Case
3 Phase Rotation Tester	4
		- Digital Phase indicator with open phase checker
		- Operational voltage 200 - 480 VAC
		- Time limit for continuous 200V : With in 60 minutes
		- Time limit for continuous 480V : With in 4 minutes
		- Frequency response 20 -400 Hz
		- With stand voltage 2200 V AC for 1 minute
Analog AC Ammeter Meter	4
		Analog AC Ammeter moving iron type
		Connect with CT measuring range 30/5A
		Fron panel 96 x 96 mm
Electrical Drill (BOSS)	2
		- Heavy duty
		- Single phase rotary hamamer drill.230 V
		- Impact energy 0 - 3 J
		- Impact at nominal speed 0 -4000 1/min
		- Nominal rated input: 800 W. Tool chuck DSD plus
		- Drilling capacity into concrete with impact drills 4 - 26 mm
		- Drilling capacity into steel 13 mm
		- Drilling capacity into wood 30 mm
		- Max Drill diameter into masonry with kernel drill 68 mm
		- Comes with impact resistant plastic box. SDS max adapter, plat chisel, moil point chisel, hammer drill set, depth gauge and additional handle
Automatic Control Motor
PLC Module	4	- Portable training kit
		- Power supply 100 -240 VAC
		- Maximum number I/O = 24 point
		- Output type: Relay
		- Integrated input: 14
		- Integrated output: 10
		- Interface cable PC to PLC
SENSOR Combine	2	- Inductive proximity sensors or switches
		- Maximum operation Distance 5 mm
		- Supply voltage 10 VDC
Control Relay	10	- Three-phase monitoring relay
		- Measuring range: 3 x 300 - 500 VAC
		- Rated Control supply Voltage (Us): 3 x 300 - 500 VAC
		- Output: 2 c/o (SPDT) contacts
		- Time Rang:
		- 200 ms start-up delay
		- 0s or 0.1 - 30 s tripping delay (ON/OFF)
Temperature Controller/ Digital	4	Temperature controller / Digital Temperature controller
		- Input Thermocouple Type: K, J, T, R, N, S, B and PT 100/ RTD.
		- Output type Relay
		- Contact 250 VAC / 3A and SSR Drive voltage 0 -12 VDC.
		- PID self tuning and ON/ OFF
		- Power supply 100 -240 VAC
Contactor	10	Three-phase main contactor
		One auxilary contact NC (230 V, 50 Hz)
		Coil Voltage 220 V, 50 Hz
Push Buttons Switch	15	Push button switch 1NO/NC
		Diameter 22 mm
		Voltage 220 VAC
Over Load Relay	5	Over Load relay uses with contactor
		Type SN 20/ ST 20 5 (4-6) A
Circuit Breaker	5	3-pol C 16A - Miniature Circuit breaker (MCB)
		According to DIN/VDE 0641/T11 for line safety Breaking Capacity / Contact rating 6 KVA single pol Triple Pole (3 Pole)
Digital timer Relay	5	Multi range delay timer:
		- Each Timing shall have 4 time ranges, selectable via DIP switch
		- Based on Microcontroller
		- Compact high performance on delay timer
		- Each timer shall have four time ranges, allowing switching to any of four set of time specification using a DIP switch on the timer body for reliable and easy operation.
		- When input voltage is applied, the timing cycle shall begins
		- At the end of the timed period the internal relay is energized.
		- Including standard 8-pin socket
		- Surface mounted timer converts to flush mounting style with optional adapter time switch, 1 pole, 16A, DIN rail 57 mm.
Pilot Lamps (3 Lamps)	20
		Pilot lamp
		Diameter 22 mm
		Voltage 220 VAC
Three phase motor	2	Three phase asynchronous Motor (1 HP)
		- Three phase 380 - 415 Volt/ 50 Hz power supply
		- Output 0.5 HP/ 0.37 kW/ 4 pole
		- Speed 1395 rpm
		- Fan Cooled
		- Food Mounted (B3)
		- IP 55 enclosure
AC Inverter	3	Portable training kit
		Power supply: 200 - 240 VAC
		Starting torque: 150% or more
		Output frequency: 0.2 - 200Hz
		Communication: RS -485 standard or USB
		Interface cable PC to inverter
Cable THAI YAZAKI THW 1*5 mm	6	THW 1.5 sqmm black/ 100 meter per roll
Electric induction Motor	4	Single phase asynchronous Motor (0.5 HP)
Foot Mounter		Single phase -220-240 Volt 50 Hz power supply
		Output Power 0.5 HP/ 0.37 kW/ 4 Pole
		Speed 1350 rpm
		Fan cooled
		Capacitor Start/ Capacitor Run
		Foot Mounted (B3)
		IP 55 Enclosure
Hand PLC Write	2	Industrial programming and maintenance tool
		This unit can perform upload/ download and store upto 15 programs in its internal memory.
		Power supply 5 VDC
		Display LCD (with blacklight)
		Keys: 35
		Memory: Allowable number of writes: 100,000 times
Computer PC-compag/ HP	2	Processor: Core i3 - 3240 (3.4 GHz)
		Graphic Card: HD Graphics/ share
		Single DDR 3 4 GB/ 1600 MHz
		Harddisk: 1 TB 7200 rpm
		Monitor 20 inch LED